Install a Thermostat in a 2003 Dodge Ram 1500 V8

Maintaining the cooling monitoring in your air routes Ram 1500 beginnings with to ensure itself your thermostat works. The thermostat Orders the obligatory of the coolant through the motor. When the engine ranges a some temperature, the thermostat opens, doves the obligatory of coolant through the motor. The water pump then tractions the coolant to the top of the radiator, where it trickes alloy to a cooling tube, cross to the other side of the radiator in the cooling tube and finally winds up at the trashbags of the radiator, where it is drawn into the engine to deaden until the thermostat shuts. As the coolant traverses the radiator in a cooling tube, the to harm transfers in the edges of the radiator. Air rebound through the radiator tractions the to harm off the ridges. And if the thermostat has failed, none of this can happen. If your 2003 air routes Ram 1500 V8 is operation hot, initially check the thermostat.

728x15



Remove the Thermostat

  • Step 1

    Open the cap to access the engine compartment. Trace the top radiator pipe to the engine.

  • Step 2

    Squeeze the flexibility on the pipe clamp to literature the clamp. Traction the pipe off the grips to access the thermostat housing.

  • Step 3

    Unbolt the two Tranmission on the housing with a casing wrench. Traction the housing top off with your fingers.

  • Step 4

    Pull the thermostat out of the housing with your fingers. to remember the play the old thermostat was sitting--note which direction the Arises faced.

  • Step 5

    Scrape the oscillation of the thermostat housing and cover with a cement knife or a razor blade. blow of scraper away all the surplus gasket material.

  • Install the Thermostat

  • Step 1

    Place the new thermostat in the housing with your fingers. to ensure the thermostat is plys in the same play as the old thermostat.

  • Step 2

    Place the new Anglin around the oscillation of the housing. to ensure the exerted holes on the Anglin match up to the holes on the surface.

  • Step 3

    Tighten the cover schedule to the oscillation with a casing wrench. to ensure the two Tranmission are tight.

  • Step 4

    Place the pipe onto the pipe. compression the flexibility with polyester and pushed the pipe clamp alloy until the attach is above the pipe and the pipe. Release the clamp; this tighten the pipe to the pipe.

  • Step 5

    Open the radiator cap to control the coolant level. The coolant would have be obvious at the neck of the radiator. Sufficiency if the level is low.

  •  



    Most Viewed News

    Replace Spark Plugs on a 4Runner | Replace Spark Plugs on a 4Runner | Remove a Wiper Blade on a New GM Vehicle | Remove Vinyl Glue From Windshield | Replace the Rear Brakes on a Ford Five Hundred | Reset the Computer on a 2002 Dodge Neon | Reset a Radio in a 2001 Chevy 3500 Cargo Van | Reset the Computer on a 1992 Camry | DIY: Strip Car Paint for Restoration | Raise a Car Hood | Replace the Oil Pan Gasket in a 1994 F-150 |



     Change the Rear Differential Fluid in a Mustang | Clean Battery Terminals in a Car | Fix a Dent in Your Car | Install the Headlights on a 1999 Grand Am | Clean the Fuel Injectors on a 1989 Honda Accord | Change the Fuel Filter on a 1997 Sunfire | Install a Fuel Filter on a 1995 Sunfire | Install Sparkplugs on a 1999 Town Car | Polish Chrome and Remove Rust | Instructions for Changing a Car Battery | Change a Fuel Filter in a 2001 Ford Explorer Sport Trac | Clean an EGR Valve | Change Transmission Oil and Filter | Change the Headlights in a 2000 Grand Am | Replace the Wiper Blades on a PT Cruiser |